Canon BJC-2000 BJC-2100 Series

1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel, Hold down the RESUME/RESET button and plug in the AC power cord
4: Release RESUME/RESET after plugging in the AC Power cord.
5: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
6: Press and HOLD RESUME/RESET for two seconds or more and release it.
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Unplug AC Power Cord to set data.

Canon GENERIC “S” SERIES RESET CODE

Waste Ink Counter Reset.

1. Turn off the printer.
2. Press and hold the RESUME button, then press and hold the POWER button.
3. Release the RESUME button, Next press and release the RESUME button two(2) more times in succession. Note: you are still holding the POWER button). The printer’s carriage will “reset” or move momentarily. If the above was properly performed the printer will enter the “Service Mode”.
4. Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp will alternate (change) color with each key press.

1. Service/Factory test printout, including ink sensor check.
2. EEPROM – Info printout.
3. EEPROM – Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point – However it is best leave them unaltered – You have been warned!) After selecting the desired mode (eg 4), press the POWER button to “set” the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.

+++++++++++

Canon PIXMA iP1000

Waste Ink Counter Reset Manual for Service mode

1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.

Canon PIXMA iP1500

Waste Ink Counter Reset. Manual for Service mode

1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green
6. Release both buttons

Canon i320, i255

Waste Ink Counter Reset.

Step 1 : Manual Temporary
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.

or Step 1: Manual Temporary
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.

step 2 : Software for Permanant

1. Reconnect the printer cable.

2.Open General Tools software and select (USB PORT)

3 .Choose (SET DESTINATION 1) And it should be reset.

Remark “After service mode Pls use software for permanent reset”

Canon i850, i950, S600

Start with the printer OFF
1. Hold down RESUME and then hold down POWER
2. release RESUME
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing

Select function with RESUME press POWER to execute:

presses – light color – function

Number of presses – light color – function

0 presses – green – Test print (or exit service mode on i960)
1 press – orange – EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses – green – EEPROM initialize
3 presses – orange – Reset waste ink counter

Canon S450 Printer

1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5. Release Power button
6: When the indicator lights steady, press RESUME three times. The indicator should be orange.
7: Press Power to set data

Canon BJC 1000 Series

1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.

Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265

Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650

Unplug Power Cord
Hold POWER and RESUME buttons
Plug in Power Cord
Release buttons
Open front door of printer
Hold the CARTRIDGE and RESUME buttons
Press POWER
Release all buttons after the beeps
Press CARTRIDGE once
Press RESUME

Canon BJC-5000

1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data

Service Test Print

1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
6: Press Power to Print

Nozzle Print

1: Power off printer
2: Press and POWER, until the printer beeps and release.

Demonstration Print

1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.

Canon BJC-5100

Self Test

Switch Printer off. Hold Power for 1 beep.

Waste Counter Reset
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data

Service Test Print

1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
6: Press Power to Print

Nozzle Print

1: Power off printer
2: Press and POWER, until the printer beeps and release.

Demonstration Print

1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.

Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620

Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500

1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three times. The indicator should be orange.

Canon BJC-600 BJC-600e BJC-610 BJC-620

1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps

Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70

1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beep
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord

Canon BJ-30 BJC-35v BJC-70

F14 Error Reset

1: Unplug adapter
2: Hold POWER
3: Plug in ADAPTER
4: Release POWER after printer starts
5: Hold FF and MENU and press POWER
6: Release after beeps
7: Press <> Cartridge until 1A is displayed
8: Press ONLINE
9: Press POWER to shutoff printer
10: Unplug printer then re-plug printer

Canon BJ F900, F890, F700, F500, S900, S820, S750 and S520

Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button. Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.

You are now in Service mode.

Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.

1. service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)

After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a resta

Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950,

PIXMA IP3000 above,

1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

Canon S900, S820, S750, S520

Turn off the printer.

Press and hold the RESUME button, then press and hold the POWER button. While still holding the POWER button, Release the RESUME button, then press and release the RESUME button two more times in succession.

The printer mechanics will move momentarily. You are now in Service mode. Release the Power Button. Pressing the RESUME key will select a function; for example, pressing

RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.

1. Service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)

After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart.

Canon S9000

Turn off printer

Hold down Resume button and press Power button. Keep holding down Power button and let Resume button go. Press Resume button 2 times then let BOTH buttons go. Green lights will flash and then stop blinking. When green lights are solid, press the Resume button 4 times. Press the Power button and the printer should turn off, if not, press
the Power button once more. Your printer should respond as normal.

Canon MPC190

Reset Waste Ink

1) Enter SERVICE MODE. By pressing Menu Copy Scan Copy Copy
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [Set] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

Source

Canon MP160 , MP145

1. With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
   
2. When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
   
3. When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
   
4. When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in orange and green, starting with orange.)note: press 4 times for waste ink counter reset.
   

The number of the Reset
button pressing
LED Function Remarks

0 time Green Power off

1. time Orange Service pattern print
   
2. times Green EEPROM print
   
3. times Orange EEPROM reset
4. times Green Waste ink counter reset
   
5. Unplug cable power. (for MP145 / MP150)
   
6. Turn Off Power. (for MP160)
   

Error Code :

1. E2-2 = No paper (ASF)
   
2. E3-3 = Paper jam
   
3. E4 = No ink
   
4. E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
   
5. E8 = Waste ink absorber full, or platen waste ink absorber full
   
6. E9 = The connected digital camera / video camera does not support Camera Direct Printing
   
7. E14 = The Ink cartridges whose destination are wrong
   
8. E15 = Ink cartridge is not installed E16 - Ink remaining is unknown
   
9. E16 -E19 = Failed to scan head alignment sheet
   
10. E22 = Carriage error
    
11. E23 = Paper feed error
    
12. E24 = Purge unit error
    
13. E25 = ASF(cam) sensor error
    
14. E26 = Internal temperature rise error
    
15. E27 = Waste ink absorber full or platen waste ink absorber full
    
16. E28 = Ink cartridge temperature rise error -
    
17. E29 = EEPROM error
    
18. E33 = Paper feed position error
    
19. E35 15 = USB Host VBUD overcurrent error - USB
    
20. E37 17 = Abnormal motor driver error
    
21. E40 20 = Other hardware error
    
22. E42 22 = Scanner error
    

MERESET WASTE INK COUNTER PADA CANON MP160 DAN MP145

1. Matikan printer (kabel power masih tercolok), tekan dan tahan tombol STOP/RESET kemudian tekan tombol ON/OFF dan lepas STOP/RESET
   
2. Tahan tombol ON/OFF, tekan tombol STOP/RESET 2x
   
3. Lepaskan kedua tombol dan printer akan masuk ke SERVICE MODE (muncul angka NOL)
   
4. Printer akan charging
   
5. Setelah printer selesai charging, tekan tombol STOP/RESET 4x.
   
6. Setiap kali tombol STOP/RESET ditekan, lampu ON/OFF akan berubah warna hijau dan oranye.
   
7. Tekan tombol ON/OFF 1X, angka berubah ke SATU (1)
   
8. Matikan printer dan cabut kabel POWER.
   
9. Hidupkan kembali printer
   

Kode Error Canon MP160 dan MP145

1. E2-2 = No paper (ASF)
   
2. E3-3 = Paper jam
   
3. E4 = No ink
   
4. E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
   
5. E8 = Waste ink absorber full, or platen waste ink absorber full
   
6. E9 = The connected digital camera / video camera does not support Camera Direct Printing
   
7. E14 = The Ink cartridges whose destination are wrong
   
8. E15 = Ink cartridge is not installed E16 - Ink remaining is unknown
   
9. E16 -E19 = Failed to scan head alignment sheet
   
10. E22 = Carriage error
    
11. E23 = Paper feed error
    
12. E24 = Purge unit error
    
13. E25 = ASF(cam) sensor error
    
14. E26 = Internal temperature rise error
    
15. E27 = Waste ink absorber full or platen waste ink absorber full
    
16. E28 = Ink cartridge temperature rise error -
    
17. E29 = EEPROM error
    
18. E33 = Paper feed position error
    
19. E35 15 = USB Host VBUD overcurrent error - USB
    
20. E37 17 = Abnormal motor driver error
    
21. E40 20 = Other hardware error
    
22. E42 22 = Scanner error

Source

Network topology is, things that explains geometric relationship between the basic elements making up the network, namely nodes, links, and the station. Network topology can be divided into 5 main categories as below.

• Star Topology
• Ring Topology 
• Bus Topology 
• Mesh topology
• Tree Topology 

Star Topology

Star topology is a form of network topologies in the form of convergence of the middle node to every node or user. Star network topology including network topology with Middle costs.

Benefit Topology star

• Damage to one channel will affect only the channel network.
• Level of security this type is High.
• Resistant to traffic of a busy network. 
• Addition and subtraction station can be done easily.

Lack Topology Star

If the center node is damage, the whole network is interrupted.

RING TOPOLOGY

Ring topology is a network topology point-shaped circuit, each of which is connected to two other points, such that form a circular path to form a ring. In the ring topology, data communication can be disrupted if a single point impaired. FDDI networks anticipate this weakness by sending data clockwise and counterclockwise at the same time.

Computer network is a system consisting of computers and other network devices that work together to achieve a common goal. The purpose of the computer network are:

•  Sharing of resources: for example, shared use of printers, CPUs, memory, hard drive
•  Communication: eg electronic mail, instant messaging, chat
•  Access to information: for example web browsing

In order to achieve the same goal, each part of the computer network and provide service request (service). Party requesting the service is called a client (client) and that provide services called the servant (the server). This architecture is called client-server systems, and is used in almost all computer network applications.

Classification Based on the scale:

•      Personal Area Network (PAN)
•      Campus Area Network (CAN)
•      Local Area Network (LAN): a computer network that connects a computer with another computer with a limited distance.
•      Metropolitant Area Network (MAN): principle the same as LAN, only the larger distance, ie 10-50 km.
•      Wide Area Network (WAN): the distance between cities, countries, and continents. This is the same with the Internet.
•      Global Area Network (GAN)

Based on the function: Basically every computer network is functioning as a client and server. But there is a network that has a dedicated computer as a server and the other as a client. There is also a computer that has no special function as a server only. Therefore, based on their function there are two types of computer networks:

     * Client-server

Network is the computer with a dedicated computer as a server. A service / service can be provided by a computer or more. An example is a domain like www.detik.com lots served by the web server computer. Or it could be a lot of service / services provided by a single computer. Examples are jtk.polban.ac.id server that is a multi-service computer with the mail servers, web servers, file servers, database servers and others.

     * Peer-to-peer

Namely computer networks where each host can be a server and also a client simultaneously. For example in the file sharing between computers on the Windows Network Neighborhood Network have 5 computers (we give the name of A, B, C, D and E) that provide access rights to the files they have. At one point A to access the file share of B named data_nilai.xls and also gives access to the file soal_uas.doc C. When accessing a file from B then A serves as a client and as a give file access to C then A serves as a server. Both functions were performed by the same A network like this is called peer to peer.

This brief tutorial really suitable for the current computer network to make cheap, especially for more than 2 clients, with using hub much cheaper than a router. What is UTP cable? UTP cable is a special cable for data transmission.

UTP is stands for "unshielded Twisted Pair". It is called unshielded because less resistant to electromagnetic interference. And called twisted pair its because there are couples who arranged spiral cable twisted each other. There are 5 categories of UTP cable. From category 1 to category 5.

Category 3 can be used for data transmission up to 10 mbps, while the category 5 for transmition data up to 100 mbps.

STRAIGHT CABLE SETTING

To Setting up this mode see bellow:

1: light orange
2: dark orange
3: light green
4: dark blue
5: light blue
6: dark green
7: light brown
8: Dark Brown

CROSS CABLE

To make this mode first step must be do is like make straight cable mode

1. light orange
2. dark orange
3. light green
4. dark blue
5. light blue
6. dark green
7. light brown
8. dark brown

and the second step we have to do is

1. light green
2. dark green
3. light orange
4. dark blue
5. light blue
6. dark orange
7. light brown
8. dark brown

LAN TESTER - a tool to test knowing the cable is connected properly or not.

For we are the beginner in the Linux and wanted to migrate from Windows to Linux we should try first a few Linux applications that we first identify previously.

May install Linux on a PC and we don't have an experience may situation like this will be trouble us.to avoid this better we have to know some of the applications we will use in Linux.

The following applications are:

• Windows Media Player / BSPLayer --> vlc, Totem
• Winamp, iTunes --> Amarok (KDE), Exaile, Rhythmbox, XMMS, BMP, Audacious, Banshee
• uTorrent / Bittorrent --> Transmissionbt, Deluge-torrent, KTorrent (KDE), Azureus
• Nero Burning ROM --> Brasero, k3b (KDE), Serpentine
• Windows Movie Maker --> Avidemux, Kino (KDE).
• 3D Studio MAX, Blender, Maya --> Blender, Maya, Softimage, K-3D (KDE)
• Internet Explorer --> Firefox, Opera, Konqueror, Epiphany
• Outlook --> Thunderbird, Evolution
• Microsoft Office --> Open Office, AbiWord, KWord
• ICQ, MSN Messenger, AIM, Yahoo Messenger --> Pidgin, Kopete, aMSN, KICQ
• FTP Client --> FileZilla, GFTP, KFTP (KDE)
• Photoshop --> GIMP
• Irfanview, ACDSee --> XnView, GQView, Mirage
• Audacity, CoolEdit, Audio Catalyst --> Ardour, Rosegarden, Audacity, Beast
• GuitarPro --> TuxGuitar
• Daemon Tools --> gmount-iso
• Partition Editor, Partition Magic --> QTparted, GParted
• Zone Alarm or any firewall --> Guarddog, Firestarter

Although we have already in Linux platform, you may still need a Windows application for typing, gaming, or other reasons. Linux and Windows are different, but Wine can put them together!

The purpose of the above is not meant to create an operating system 'hodgepodge' of Windows and Linux, but simply an application program that makes Windows feel as if running on Windows systems, although running on a Linux system. This program is called the emulator and emulator we meant is Wine.

Wine is typically used by users of Windows while in using Linux os because they are unfamiliar with native applications Linux. With Wine, Windows applications can be executed directly without the need to move to the Windows operating system.
May be the question: "Does Windows and Linux is an operating system that is technically different? Can Wine emulate Windows applications that can run in linux like its original condition? ". The answer is no. In general, there are things that can be emulated by Wine, some are not. A Windows program that all functions run perfectly on Windows may not function properly when diemulasi Wine. Even some Windows programs that refuse to work at all when emulated by Wine. All these risks must be aware of before running your Windows applications with Wine.

You may also be asked: "What difference does it make Windows applications run by VMWare (or similar programs like Qemu) with applications that run Wine?". The answer can you see in the following explanation.

• Wine does not require as much memory VMWare. Thus, the available memory (free memory) is greater than when using VMWare. These benefits will be felt if you plan to run more than one Windows application in Wine.
• Collaboration antaraplikasi Windows and Linux programs natively (eg when running copy and paste functions) becomes easier because the two programs are treated the same under Linux.

• Wine does not simulate the entire PC system as well as VMWare so that execution of the program in the Wine became faster.

How to get wine

type the following command below after u on the root

sudo apt-get install wine

source www.chip.co.id

Setting IP ADDRESS on Linux really is really  easy as setting the IP ADDRESS windows machine. GUI Front for any IP Address Setting It's much better on Linux GTK, QT, as well as Curses based on Slackware's pkgtool.

But it's good that we know how to set IP address manually, because maybe someday we will be faced with a situation where we can not use the Desktop System at all.

In doing Setting IP Address on Linux the first thing to note is the address or the naming of Ethernet to be used, for example eth0, eth1, the DST. After the naming of Ethernet Device is known, then the next step is to set IP Address by using the following this command.

for the first step we must login to the root after we have already on the root type this command.

ifconfig eth0 192.168.0.1

command is an illustration of setting the IP address 192.168.0.1 on interface eth0.

ifconfig eth0 192.168.0.1 netmask 255.255.255.0

Command is illustrated by setting IP address 192.168.0.1 on interface eth0 all used to determine the netmask.
After the IP Address defined the next step is setting up the default gateway to be used, can be done with the command.

route add default gw 192.168.0.10

Illustrates the setup of the command that the default gateway will be used on the IP address 192.168.0.10. The next step is to do the DNS settings to use, it can be done by editing the file "/ etc / resolv.conf" to determine the address of the DNS is used.

nameserver 192.168.10.10  nameserver 202.125.256.12

Modem stands for Modulator demodulator. Modulator is part of changing the information signal into the carrier signal (Carrier) and is ready to be sent, while the demodulator is the part that separates the information signal (which contain data or messages) of the carrier signal (carrier) that accepted that the information can be received well. Modem is a merger of both, it means the modem is a two-way communication tool. Each remote communications device of two-way commonly use the so-called "modern", such as VSAT, microwave radio, etc., but generally the more modern term known as the hardware is often used for communications on the computer.

Data from the computer in the form of digital signal provided to a modem to convert into analog signals. Analog signals can be transmitted through several media such as mobile telecommunications and radio.

On arrival at the destination modem, the analog signal is converted into digital signals and transmitted back to the computer. There are two types of modems are physical,  external modem and internal modem.

• ADSL MODEM

ADSL modem (Asymetric Digital Subscribe Line) technology that allows surfing the Internet and use the analog phone simultaneously. ADSL is given a device called a Splitter or divider line.

Splitter position when placed in front of the line calls. This means you can not graft the ADSL modem line with direct sound. Splitter useful tool to eliminate noise when you are using ADSL modem. With Splitter both can go together, where you may be able to answer and call someone with a regular phone. On the other hand you can still connect to the Internet via ADSL modem.

• CABEL MODEM